Does anyone have the SD-1 and DS1 mods
-
- Posts: 8
- Joined: Wed Aug 29, 2018 6:50 pm
Does anyone have the SD-1 and DS1 mods
Does anyone have some of the mods to put in here?
Re: Does anyone have the SD-1 and DS1 mods
(This is from the old Keely website)
Boss SD-1 5-Star Ge Keeley Mod
Keeley Custom Shop designed this mod to enhance the tone and functionality of the SD-1.
Freely copy and distribute. We have the right to change our modifications at any time without notification. It is fun to watch what big name people use the mods.
Board Number, New part, Old part, Reason, Where to get the part
C10 --> Metal Stack Film 1uF, remove electrolytic, increased fidelity, digikey
C7--> Metal Stack Film 1uF, remove electrolytic, increased fidelity, digikey
R6 --> 2.4k ohm metal film, 4.7k, increased distortion, digikey
C3--> 0.1uf metal stack film, 0.047uf, fidelity and bass response, digikey
C2--> 0.1uf metal stack film, 0.018 fidelity and bass response, digikey
R2--> 620k ohm metal film, 470k ohm, increased input impedance, better bypass, digikey
Add 47pF cap across diodes in clipping section to smooth out distortion, just like TS9, radio shack
On some older units, short out D3 and the 470 ohm resistor in the power supply section to increase the voltage to the circuit. This increase the headroom and gain. Newer units have it shorted already.
Here is the tricky part of our mod, take a germanium (Ge) transistor and use the Base-Emitter junction (legs) of the device and use it in place of D6. If you use a PNP transistor, the Base will be the negative or cathode side, the Emitter will be the anode. Here is a diode drawing Cathode---|<----Anode. This increases the amount of distortion produced by the pedal, it also sound really nice. Try this! Don't leave it out! It's fun. Get your Ge transistors from Steve Daniels http://www.smallbearelec.com/
If you want to drill out the LED and install a 5mm big job, change R30 to a 1.2k-3.3k ohm depending on brightness and battery drain you want, replacing the stock 3.9k ohm.
Boss SD-1 5-Star Ge Keeley Mod
Keeley Custom Shop designed this mod to enhance the tone and functionality of the SD-1.
Freely copy and distribute. We have the right to change our modifications at any time without notification. It is fun to watch what big name people use the mods.
Board Number, New part, Old part, Reason, Where to get the part
C10 --> Metal Stack Film 1uF, remove electrolytic, increased fidelity, digikey
C7--> Metal Stack Film 1uF, remove electrolytic, increased fidelity, digikey
R6 --> 2.4k ohm metal film, 4.7k, increased distortion, digikey
C3--> 0.1uf metal stack film, 0.047uf, fidelity and bass response, digikey
C2--> 0.1uf metal stack film, 0.018 fidelity and bass response, digikey
R2--> 620k ohm metal film, 470k ohm, increased input impedance, better bypass, digikey
Add 47pF cap across diodes in clipping section to smooth out distortion, just like TS9, radio shack
On some older units, short out D3 and the 470 ohm resistor in the power supply section to increase the voltage to the circuit. This increase the headroom and gain. Newer units have it shorted already.
Here is the tricky part of our mod, take a germanium (Ge) transistor and use the Base-Emitter junction (legs) of the device and use it in place of D6. If you use a PNP transistor, the Base will be the negative or cathode side, the Emitter will be the anode. Here is a diode drawing Cathode---|<----Anode. This increases the amount of distortion produced by the pedal, it also sound really nice. Try this! Don't leave it out! It's fun. Get your Ge transistors from Steve Daniels http://www.smallbearelec.com/
If you want to drill out the LED and install a 5mm big job, change R30 to a 1.2k-3.3k ohm depending on brightness and battery drain you want, replacing the stock 3.9k ohm.
- Pepe
- Posts: 1685
- Joined: Thu Aug 16, 2018 2:19 pm
- Location: Germany
- SBZ: Multi Platinum
- Bossarea: Double Platinum
- Contact:
Re: Does anyone have the SD-1 and DS1 mods
Off topic: great to see you in the new forum, cctsim! I hope you and your family are doing great!
Re: Does anyone have the SD-1 and DS1 mods
Hi Pepe, many thanks for the welcome. Best wishes to you and your family too.
Re: Does anyone have the SD-1 and DS1 mods
On the subject of modding Boss pedals, does anyone know if Boss has changed the SD-1 to SMD components on the current models?. They changed the DS-1 and BD-2 to SMD a couple of years ago, and wonder if they are going to change more of the vintage OD/distortion pedals to this contruction. It will make modding harder for people who don't know how to work with SMD circuits.
Al
Al
Re: Does anyone have the SD-1 and DS1 mods
I did a so called circuit bending on a DS-1, bought cheap, and it sounds nothing like a stock DS-1, really wild.
Don´t ask me what I´ve done, as I changed and changed and changed component values, even removed components and soldered connections between different "parts".
This was really fun to do.
I also was given a dysfunctional PH-3 from a friend, and I couldn´t repair it, to build a fuzz in it, with true bypass and a hidden foot-switch. The foot-switch was really hard to get right.
Don´t ask me what I´ve done, as I changed and changed and changed component values, even removed components and soldered connections between different "parts".
This was really fun to do.
I also was given a dysfunctional PH-3 from a friend, and I couldn´t repair it, to build a fuzz in it, with true bypass and a hidden foot-switch. The foot-switch was really hard to get right.
Re: Does anyone have the SD-1 and DS1 mods
The only thing you didn't fix on that is the rubber grommet, really??!?
Nice build though.
Nice build though.
"People who are late are usually in a better mood than the people waiting for them to show up."